You do not need to worry so much. Because you will always find a way how to do it. You can always find a solution to a problem. Just follow the step by step process. To make the project successful.Get ready all the stuff that is needed. And see the outcomes after. And be amazed of the results.
Put them in one place together. And have a copy of the instructions so you it will not be very difficult. Get a piece of paper if you have not tried this before. And make sure that you follow everything and the way they instruct you to do it. It is necessary so you will be successful in doing the Reflow soldering oven. Do not invent something if you have no enough basis for it. To avoid accident.
Once you have it already, then get a thermometer and also a timer. These two could be use to determine you their temperature. Oven toasters have their own timer, but you would be using one to check the pcb. If they are hot enough already.
You can now creates a motherboard. Just ensure the size of your board will fit into your oven. Measure the size and then that would be the size you should be using.This is the floor plan. And everything you need to test must be put in here. So be careful in making them. And check if all components are complete.
After you are done making them, you may now add some flux so you could modify later. This is very important that you put them on top of the board to avoid the balls from flowing to any location. So the reflow will become successful.
Then align all the components inside. Lay them down on the flat surface. Most will use a silk screen for easy viewing of the different activities. Watch them they are slowly melt and changes its present state. Best that you will not leave them. So you could monitor.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If the time is over, then open the door. So they will cool faster. This is the only way for you to cool them down. Never touch anything on the surface especially the components. Since they are still in liquid state. If you notice the temperature that it is already 50 degree Celsius, then it is a sign to take them out.
Check them after. You have to check after. This is necessary that all components are still present. And you have achieved what you wanted. When all have been connected then, it is a sign that you are successful.
Put them in one place together. And have a copy of the instructions so you it will not be very difficult. Get a piece of paper if you have not tried this before. And make sure that you follow everything and the way they instruct you to do it. It is necessary so you will be successful in doing the Reflow soldering oven. Do not invent something if you have no enough basis for it. To avoid accident.
Once you have it already, then get a thermometer and also a timer. These two could be use to determine you their temperature. Oven toasters have their own timer, but you would be using one to check the pcb. If they are hot enough already.
You can now creates a motherboard. Just ensure the size of your board will fit into your oven. Measure the size and then that would be the size you should be using.This is the floor plan. And everything you need to test must be put in here. So be careful in making them. And check if all components are complete.
After you are done making them, you may now add some flux so you could modify later. This is very important that you put them on top of the board to avoid the balls from flowing to any location. So the reflow will become successful.
Then align all the components inside. Lay them down on the flat surface. Most will use a silk screen for easy viewing of the different activities. Watch them they are slowly melt and changes its present state. Best that you will not leave them. So you could monitor.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If the time is over, then open the door. So they will cool faster. This is the only way for you to cool them down. Never touch anything on the surface especially the components. Since they are still in liquid state. If you notice the temperature that it is already 50 degree Celsius, then it is a sign to take them out.
Check them after. You have to check after. This is necessary that all components are still present. And you have achieved what you wanted. When all have been connected then, it is a sign that you are successful.
About the Author:
When you are searching for the facts about a reflow soldering oven, go to our website today. More details can be seen at http://www.sikama.com now.
No comments:
Post a Comment