Installation of an ice maker water line is a fairly simple task that a handyman can complete in an hour or two if they have a little knowledge and the right set of tools. However, there are a few things that can go awry and cause damage to your home if not done properly. Even some special installation kits and tools can lead you in the wrong direction, causing leaks in the future. Installing ice maker Water lines bellevue wa is an easy job to do by yourself.
In the past, you could only use a quarter inch copper pipe to connect the ice maker to the nearest source of hydro, these days there are a quarter inch flex pipes that come in different lengths from 1' to 20' that you can use to connect to any hydro source. You only need to calculate how far your hydro line will need to be run to buy the pipe with the right length.
First off, when you call the plumbing company, ask for their license number. This is important because if the plumbing company is not licensed, then they are not a legitimate contracting company. And if one of their employees gets hurt while working at your home, or if something massive is damaged at your home because of their work, you will actually be held responsible since you hired an unlicensed and uninsured company.
Second, ask about what their process is for replacing the main water line. If you care at all about your landscaping, you will make sure that they use a trenchless piping method so that they do not have to dig out your entire back yard in order to replace the busted pipe.
While almost anyone can go to an equipment rental place and get equipment to remove the hydro, it is likely the rental equipment is less than stellar in its upkeep and, even if maintained to specs, may not perform to the same level as a professional's equipment even when the rental equipment was brand new.
Locate the angle stop around or under the sink area where you will be tying the line. Close the faucet and shut off hydro to the angle stop. Make sure that you disconnect the flex line running from the angle stop. You might have to use two sets of pliers to remove the line safely. Pliers should be used to attach the angle stop and hold it in place, and the other should be used to unscrew the flex line.
Now, you can attach the Tee Adapter. The adapter should connect to the hydro stop valve, and it should be sized to fit the valve. The important thing is to make sure that the outlet has a quarter inch OD. Tighten the Adapt-A-Tee to the angle stop.
Tighten it as much as you can and use a wrench if you have to but be careful not to move the angle stop while you are tightening. Reconnect the hydro supply line to the 3 by 8 inch end of the Adapt-A Tee. Hold it as you tighten the line connection. Connect the a quarter inch flex line to the Adapt-A-Tee and tighten.
In the past, you could only use a quarter inch copper pipe to connect the ice maker to the nearest source of hydro, these days there are a quarter inch flex pipes that come in different lengths from 1' to 20' that you can use to connect to any hydro source. You only need to calculate how far your hydro line will need to be run to buy the pipe with the right length.
First off, when you call the plumbing company, ask for their license number. This is important because if the plumbing company is not licensed, then they are not a legitimate contracting company. And if one of their employees gets hurt while working at your home, or if something massive is damaged at your home because of their work, you will actually be held responsible since you hired an unlicensed and uninsured company.
Second, ask about what their process is for replacing the main water line. If you care at all about your landscaping, you will make sure that they use a trenchless piping method so that they do not have to dig out your entire back yard in order to replace the busted pipe.
While almost anyone can go to an equipment rental place and get equipment to remove the hydro, it is likely the rental equipment is less than stellar in its upkeep and, even if maintained to specs, may not perform to the same level as a professional's equipment even when the rental equipment was brand new.
Locate the angle stop around or under the sink area where you will be tying the line. Close the faucet and shut off hydro to the angle stop. Make sure that you disconnect the flex line running from the angle stop. You might have to use two sets of pliers to remove the line safely. Pliers should be used to attach the angle stop and hold it in place, and the other should be used to unscrew the flex line.
Now, you can attach the Tee Adapter. The adapter should connect to the hydro stop valve, and it should be sized to fit the valve. The important thing is to make sure that the outlet has a quarter inch OD. Tighten the Adapt-A-Tee to the angle stop.
Tighten it as much as you can and use a wrench if you have to but be careful not to move the angle stop while you are tightening. Reconnect the hydro supply line to the 3 by 8 inch end of the Adapt-A Tee. Hold it as you tighten the line connection. Connect the a quarter inch flex line to the Adapt-A-Tee and tighten.
About the Author:
You can find a detailed overview of the factors that determine the cost to repair water lines Bellevue WA area at http://www.foxph.com/water-lines-repair-replacement-new right now.
No comments:
Post a Comment